EPG Multi STACK Water Fuel Cell 

 

Stanley A Meyer EPG Stack
Stanley A Meyer EPG Stack

The flow rate of the slurry was about 50 ips in the ferrofluid

systems (single tier systems) ref: tech


The circumference of the mechanical EPG series (single tier systems) was about 50 inches ref rwg replication


Tthe flashing timing led rate was about 60 times/minute in the single tier system ref :Dealership tape 

By adjusting the flow rate and rate of magnetization in the alignment coils ,the magnetized portions of the ferrofluid and/or


mag-gas are synchronized to the position of the pickup coils. This reduces the back eddy current and Lorenz forces while


the slurry or gas are circulated  The maggas systems were likely tuned in a similar manner although the  90 ips reported '


for multi-tier is due to higher speed required to compensate for the lower magnetic flux per cubic inch
but  this is compensated by a greater number of windings in the multi-tier systems 

INtegrated Energy System.jpg
INtegrated Energy System RENOVATED (1).j
INtegrated Energy System RENOVATED.jpg
Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack

NOTE also See Gas Battery  Here 

Stanley Meyers Stacked Electrolyzer Volt
Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack

NOTE also See Gas Stacked Resonant Cavity Here  

Stanley Meyers Stacked Electrolyzer Volt
Stanley Meyers Stacked Electrolyzer Volt
Stanley Meyers Stacked Electrolyzer Volt
Stanley Meyers Stacked Electrolyzer Volt
Stanley A Meyer Water Fuel cell Stack

IMPORTANT: Remember, this is just a notification.  

:  6 tier epg system had Bakelite(r) pin connectors as taps on  each of the spiral tiers. 

Power connectors having pins were inserted into these plug like connectors and a threaded ring was turned to form a good connection similar  to compression joints in plumbing

        Since the Home Electrical Power System was designed as a 3 phase system 220 volt system ,.
      for this application. One could  wire all the tiers in series but this was going exceed the current capacity of the
        wire gauge used so by dividing the  current load overheating of the wire insulation was minimized'

        Since this was such a disruptive technology, there was a National Security Order placed on the EPG technology
        and Stan stopped displaying the device publicly. 

 

In the video "It Runs on Water" the FBI Federal Premises Label
        can seen on the door a Stan enters his house/laboratory and using the alarm that had been installed

        Because of his involvement with Star Wars Defense System and the need at that time for a compact source of
        power for charging capacitor banks for the satellite lasers  and also the related technological research into
        gravity shielding and electro gravaimetrics that were later developed further in the B2 and TR3B platforms
        there was now way that the technology was going to be allowed to continue.

       It was also thought that the economic effect on the PetroDollar and stability of the Mid East would likely be adverse,

if you look closely at the area between the top two tiers of the 6T mag gas plasma
image you might see the shadow of the wiring harness on the wall  SMEPG022 (The front lighting is shining through the tiers.
The reddish colored harnesses distribute power load until is is collected by the Amphicol connectors
running vertically on a support strut.

The bright blob in some of the other images is an aluminum angle brace.
Stan used the same angled material to hold the 10 switches at the bottom of the vertical cluster  array demonstration unit.
But I would not rule out insulation or cooling
In one redacted video that was viewed  the questioner was asking  about power and Stan's response
was clipped but not before saying the syllables  "cryo".. then.beeeep..edit.....Heat generated by the EPG was expected

to rise in the center  "chimney" formed by the tiers with cooler air flowing in from the side
between the tiers.

In transformers not under load "copper losses"  in the primary due to resistance
give rise to thermal effects but since in the demonstrations, the pickup up coils were  not attached to
heavy loads other than  the row  of incandescent lights used as an electron well in the electron extraction circuits
heating was not expected to be an issue.  A watt meter could be used to show the principal of power generation if the 
velocity of the magnetic gas/slurry was reduced.

Insulation around the pick-up coils on the would tend to hold heat in, not dissipate it.

( This should be read carefully as we believe the system runs cold) 

Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack

In these Version We attempt to Stack the Cells We have not put the  inter tubing or balance drain tube on yet in these postures more pictures will come also more advanced  versions .  It is Expected that you know that Stan was also using ultrasonic vibration  this can be replicated with a ultra sonic fogger and you can change out led for correct 640 nm red wave length together we can change the world do share back to dan so we can forward teach as you build 

Note Fogger will go in the center  of each cell array  the cells will need wind cut like gas processor to allow light in  will work with out cur in cell also 

GOD SPEED 

Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack
Stanley A Meyer Water Fuel cell Stack

Stay Tuned Secure Supplies has Some very very exciting new stacked cells coming soon!